Search Results: ED*

GTNE-SVX001B-EN_08212020

Document Title:	Tubular Gas Fired Direct Spark Propeller Unit Heaters
Publication Type:	Installation Operation and Maintenance
Publication Date:	2020-08-21

, severe personal injury, or death. WARNINGThis product must be installed by a licensed plumber or gas fitter when installed within the Commonwealth of Massachusetts. Installation must be made in accordance with local codes, or in absence of local codes, with the latest edition of ANSI Standard Z223.1

GUNE-SVX001C-EN_05042022

Document Title:	Tubular Indoor Gas Fired Duct Furnace
Publication Type:	Installation Operation and Maintenance
Publication Date:	2022-05-04

were applicable at the time the design was certified. • Installation must be made in accordance with local codes, or in absence of local codes, with the latest edition of the National Fuel Gas Code, ANSI Standard Z223.1 (NFPA 54). WARNING Follow EHS Policies! Failure to follow instructions below could

UH-SVN001B-EN_04242020

Document Title:	Horizontal/Vertical Combustion Air Inlet Kit Category III Venting for Separated Combustion Tubular Gas Fired Unit Heaters Five-Inch Kit for 100,000 to 250,000 Btu/h Units Six-Inch Kit for 300,000 to 400,000 Btu/h Units
Publication Type:	Installation
Publication Date:	2020-04-24

) 6 in.(152.4 mm) 17.125 in.(435.0 mm) 10 in.(254.0 mm) 14.125 in.(358.8 mm) 7.25 in.(184.2 mm) UH-SVN001B-EN 7 8 UH-SVN001B-EN Venting All unit heaters must be vented! All Venting installations shall be in accordance with the latest edition of Part 7, Venting of Equipment of the National Fuel Gas

UH-SVX01A-EN_09032008

Document Title:	S and P Unit Heaters
Publication Type:	Installation Operation and Maintenance
Publication Date:	2008-09-03

Damage! Insure that all power sources conform to the requirements of the unit heater or damage to the unit will result! Follow installation instructions CAREFULLY to avoid creating unsafe conditions. All external wiring must conform to applicable current local codes, and to the latest edition of

MUA-SVN01A-EN_07012005

InstructionsInspect shipment immediately when received to determine if any damage has occurred to the unit during ship-ment. After the unit has been uncrat-ed, check for any visible damage to the unit. If any damage is found, the con-signee should sign the bill of lading in-dicating such damage and

AFDJ-PRC001B-EN_03172020

to mitigate harmonics. The innovative PowerFlex 7000 with Direct-to-Drive technology connects the power supply directly to the MV drive without an isolation transformer. Leading edge technology combines three innovations to achieve transformerless Direct-to-Drive technology: the Symmetrical Gate

AFDG-SVU01L-EN_05122020

cables and devices to assure no abrasion is occurring from vibrations against chassis of cabinets, or other edges. 11. Ensure the drive interior and exterior is clear of any dust or debris. Fans, circuit boards, vents etc. must be clean. Only use a vacuum for cleaning. DO NOT use compressed air. 12

UHEC-IN-35_04011997

from the thermostat tothe unit must be copper. Plug thecable entrance hole to preventdrafts from affecting thermostatoperation. 5. Remove the thermostat cover bypulling up at the bottom edge ofthe cover until it snaps free of thelocking springs. Before mountingthe thermostat, set the

UHEC-IN-34_04011997

tothe unit must be copper. Plug thecable entrance hole to preventdrafts from affecting thermostatoperation. 5. Remove the thermostat cover bypulling up at the bottom edge ofthe cover until it snaps free of thelocking springs. Before mountingthe thermostat, set the heatanticipator to correspond with

RRU-SVX01F-EN_11012021

chapter. • Updated System Configuration and Pre-Start chapter. • Updated Alarms and Troubleshooting chapter. • Running edits. WARNING Safety Alert! Failure to follow instructions below could result in death or serious injury. In addition to the following tasks, you MUST: • Follow all instructions in the