Search Results: ED*

18-CH82D1-1A-EN_07062020

Document Title:	Installer's Guide Direct Vent Furnace or Boiler Side Wall Vent Kit BAYVENTCN200B
Publication Type:	Installation
Publication Date:	2020-07-29

, wiring, plumbing, and flue connections must be adhered to. In the absence of local codes, the installation must conform with the National Fuel Gas Code ANSI Z223.1 "latest edition", or CAN/CGA B149 Installation Codes. The latest code may be obtained from: The American Gas Association Laboratories

18-CH84D1-1B-EN_07032020

Document Title:	Installer's Guide Dual Return Kit for S-Series Furnaces BAYLIFTB, BAYLIFTC, BAYLIFTD
Publication Type:	Installation
Publication Date:	2020-07-29

Edge Hazard. Be careful of sharp edges on equipment or any cuts made on sheet metal while installing or servicing. Personal injury may result. Important: Do not screw, cut, or otherwise puncture the unit cabinet in any location other than those illustrated in this Installer's Guide or in an approved

18-CH86D1-1A-EN_07202020

Document Title:	Installer's Guide Slim Fit Filter Box Kit for S-Series Furnace BAYSF1165AA
Publication Type:	Installation
Publication Date:	2020-07-29

result in personal injury and/or property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. CAUTIONSAFETY HAZARD! Sharp Edge Hazard. Be careful of sharp edges on equipment or any cuts made on

18-CH90D1-1A-EN_07062020

Document Title:	Service Installer's Guide KIT18092 C1 Replacement Inducer Furnace Model Families UD040C924, UC040C930** (May be A or T, ** May be "A" - "Z")
Publication Type:	Installation
Publication Date:	2020-07-30

. ss WARNING!The cabinet must have an uninterrupted or unbroken ground according to National Electrical Code, ANSI/NFPA 70 - "lat-est edition" and Canadian Electrical Code, CSA C22.1 or local codes to minimize personal injury if an electrical fault should occur. A failure to follow this warning could

18-CH92D1-1A-EN_07062020

Document Title:	Service Installer's Guide KIT18109 SiNi 80 Volt Igniter Conversion to SiNi 120 Volt Igniter
Publication Type:	Installation
Publication Date:	2020-07-30

result in severe burns. ss WARNING!The cabinet must have an uninterrupted or unbroken ground according to National Electrical Code, ANSI/NFPA 70 - "lat-est edition" and Canadian Electrical Code, CSA C22.1 or local codes to minimize personal injury if an electrical fault should occur. A failure to

18-CH93D1-1A-EN_07062020

Document Title:	Installer's Guide 80 Volt Igniter Conversion to 120 Volt Igniter KIT18110
Publication Type:	Installation
Publication Date:	2020-07-30

follow this warning could result in severe burns. ss WARNING!The cabinet must have an uninterrupted or unbroken ground according to National Electrical Code, ANSI/NFPA 70 - "lat-est edition" and Canadian Electrical Code, CSA C22.1 or local codes to minimize personal injury if an electrical fault

18-CH95D1-1B-EN_07032020

Document Title:	Installer's Guide Downflow Adapter Kit BAYVENT600A
Publication Type:	Installation
Publication Date:	2020-07-29

and/or property damage. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. Section 2. General Information Open and inspect contents for damage or missing items. CAUTIONSAFETY HAZARD! Sharp Edge

18-CH96D1-1A-EN_07292020

Document Title:	Installer's Guide Filter Access Door Kit for Downflow Furnaces BAYFLTR206
Publication Type:	Installation
Publication Date:	2020-07-31

. INSTALLATION1. Cut a rectangular opening 16” x 4-7/8” in the front side of the return air planum. Locate the lower edge of the opening 1” above the furnace and 1-1/2” from the left side of the duct. (See Figure 1). 2. Drill a 5/16” diameter hole, on the centerline of the upper edge of the opening

18-CH99D1-1_01012019

Document Title:	Installer's Guide Flue Box Kit BOX03706, BOX0377, BOX03708, BOX03709
Publication Type:	Installation
Publication Date:	2019-01-01

No. Description Qty 1 A340089P01 PRESSURE SWITCH TUBE 12 D345926P01 FLUE BOX 13 18-CH99CHD1-1 INSTALLER'S GUIDE 1 SHARP EDGE HAZARD!Failure to follow this Caution could result in property damage or personal injury. Be careful of sharp edges on equipment or any cuts made on sheet metal while

18-EB26D1-16A-EN_07082020

Document Title:	Installer's Guide Single Packaged, Cooling w/ Electric Heat, 14 SEER, Convertible, 2 - 5 Ton, R-410A
Publication Type:	Installation
Publication Date:	2020-07-08

ducts and sleeper rails rather than a curb or frame, use the following procedure: 1. Locate and secure the sleeper rails to the roof by bolting. Three (3) sleeper rails are required. One on each end to support the edges of the unit and one across the center of the unit. The cen-ter rail must run inside