Search Results: ED*

18-CH12D15-1B-EN_03042023

Document Title:	Installers Guide - Unitary Accessories. Downflow Gas-Fired Furnace Subbase. Model BAYBASE205
Publication Type:	Installation
Publication Date:	2023-04-03

) up. These will be used to locate and secure the furnace. 9. Set the base on the floor over the opening.10. Secure the base to the edge of the flooring with screws or nails through the four holes provided under the side tabs.11. Position insulaton over the subbase.12. Insert the supply duct

18-CH107D1-1C-EN_05312023

Document Title:	Installer's Guide High Altitude Conversion Kit for L8 Furnaces Kit Models: BAYHALTMOD0008, BAYHALTMOD0009, BAYHALTMOD0010, BAYHALTMOD0011
Publication Type:	Installation
Publication Date:	2023-05-31

with the reduced firing input rates required for high altitude installations, the induced draft blower has ample capacity to provide sufficient combustion air for proper and safe operation. Refer to the National Fuel Gas Code - latest Edition 11.1.2 - High Altitude and Table E.1.1(d). Installer’s

L8V1-SVX001-1A-EN_05232023

Document Title:	Installation, Operation, and Maintenance - Upflow/Horizontal Left/Right Gas-Fired, Single Stage Induced Draft Furnace with Variable Speed Blower Motor, L8V1
Publication Type:	Installation Operation and Maintenance
Publication Date:	2023-05-31

13.2 13.7 Max. Overcurrent Protection (Amps) 15 15 15 15 PIPE CONN. SIZE (in.) 1/2 1/2 1/2 1/2(a) Central Furnace heating designs are certified to ANSI Z21.47 — latest edition.(b) For U.S. applications, above input ratings (BTUH) are up to 2,000 feet, derate 4% per 1,000 feet for elevations above 2,000

P0V0-SVX001-1A-EN_05312023

Document Title:	Installation, Operation, and Maintenance - Modular Blowers - No Heat, P0V0 models
Publication Type:	Installation Operation and Maintenance
Publication Date:	2023-05-31

wiring connections andto determine specific requirements. All field wiring to the modular blower should beinstalled in accordance with the latest edition of theNational Electric Code NFPA No. 70 and any localcodes. Check rating plates on unit for rated volts,minimum circuit ampacity and maximum

88-MACC025-1C-EN_06082023

installation manual. Observe all safety warnings. During installation or repair, caution is to be observed. It is your responsibility to install the product safely and to educate the customer on its safe use. STEP 1. Unfasten 4 screws to take away the blower access panel of the air handler. 4 STEP 2

18-CH66D1-5B-EN_06122023

Document Title:	Installer's Guide - Installation instructions for KIT16582, KIT16583, KIT16584 and KIT16585
Publication Type:	Installation
Publication Date:	2023-06-12

PROPERTY DAMAGE, PERSONAL INJURY OR DEATH. CAUTIONSharp Edge Hazard. Be careful of sharp edges on equip-ment or any cuts made on sheet metal while installing or servicing. Personal injury may result. 18-CH66D1-5B-EN CAUTIONThe IFC is polarity sensitive. The hot leg of the 115 VAC power must be

18-GJ85D1-1C-EN_07172023

as close as possible to the twist out hole edges to ensure an air tight fit with breaker(s). 4. With the breakers and air handler blower door in place, set the seal kit over the breakers to cover the blower door knockout. FIGURE 2 TEMBRKSEALKT25A 4-20kW Heaters 4-20kW Heaters 25kW Heaters (All 3) 15

18-HD99D1-1A-EN_08112023

Document Title:	SC360 System Controller / UX360 Smart Thermostat, Zoning Installation Guide
Publication Type:	Installation
Publication Date:	2023-08-11

. Brand Modes: Zone Name [Zone 1-6]Zone names are defaulted to Zone 1 to Zone 6. Zone name can be select ed from a list or set to a custom name. Zone Priority Low/(Med]/High Customizable setting to specify each zone’s relative priority within the calculations for control of thezones’ capacity and

18-HE72D1-3B-EN_07062023

Document Title:	Installers guide - Duct Shroud Cover Kit (for Horizontal Ducts) BAYCOVR112 for TC/WC/YC/DC 018-60A, BAYCOVR118A for TC/WC/YC/DC* *018-60A
Publication Type:	Installation
Publication Date:	2023-07-14

top using the #10 x 3/4” screws provided. See Figure 1.2. Dig two trenches between the unit and the building large enough to insert the bottom edge of each side of the cover.3. Loosen up the screws above the horizontal openings on the unit cabinet base. Slide the top of the duct shroud with the “U

18-HE79D1-1E-EN_07062023

Document Title:	Installers Guide - Square to Round Adaptor Kit, Models: BAYSQRD001 and BAYSQRD002
Publication Type:	Installation
Publication Date:	2023-07-14

adaptors over the supply opening. Align the adaptor so that the left side edge of the adaptor flange is flush to the side of the mitred corner post on the cabinet, and the bottom flange of the adaptor is flush with the bottom of the cabinet. Secure with sheet metal screws. See Figure 1. Figure 1