Search Results: 18-CH83D1-1B-EN

BAS-SVX092D-EN_01102026

BO9 Outdoor Air Damper Typical Applications and Terminations 18 BAS-SVX092D-EN Table 6. Factory programmed terminations for single compressor control for Trane EX/DX units (continued) Inputs/Outputs/Communication Symbio 400–B/500 ControllerTerminations Factory Programmed Assumed Terminations Analog

CLCH-SVX016C-EN_12012025

— — — — —67.136 67.136 67.136 — — —997 1021 1060 - 650 MBh — — — — — — — —66.006 66.006 66.006 1348 1391 1453 Dimensions and Weights 18 CLCH-SVX016C-EN Table 6. Section dimensions (inches) and weights (pounds) — unit sizes 3 to 30 (continued) Unit size 3 4 6 8 10 12 14 17 21 25 30 - 970 MBh

88-MACC010-1G-EN_10102022

Document Title:	Installer's Guide Supplemental Electric Heaters BAYHTR1
Publication Type:	Installation
Publication Date:	2022-10-14

88-MACC010-1G-EN SSAAFFEETTYY WWAARRNNIINNGGOnly qualified personnel should install and service the equipment. The installation, starting up, and servicing of heating, ventilating, and air-conditioningequipment can be hazardous and requires specific knowledge and training. Improperly installed

BAS-PTS008A-EN_11152024

Symbio™ 800 Integration Points List LonTalk®Agility™ Water-cooled Chillers Date: 11/15/2024 Reference Document: BAS-SVP084*-EN Profile Definition and Network Variables The following tables are sorted as follows: • Tables are listed by unit/profile type and sorted by network variable number

FNR-SVN001A-EN_10182025

Document Title:	BACS9V2CA22MUAA
Publication Type:	Installation
Publication Date:	2025-10-18

. Inducer limit switch wiring 16. Disconnect the 4–pin inducer wire harness. Preparing the Furnace for Kit Installation FNR-SVN001A-EN 9 Figure 13. 4–pin inducer wire harness 17. Loosen the 3–5/16 inch screws on the inducer andremove the inducer. Retain the screws. Figure 14. Inducer 18. Disconnect the

CLCH-SVX010E-EN_08152024

GasketGasket 18 CLCH-SVX010E-EN Installation - Mechanical Figure 18. Wall section assembly Add caulking afterinstalling J strip #8 x 1-in. Phillips zip screw2 3/4-in. wide joining strip Wall split 4-in. x 1/4-in. gasketAdd caulking beforeinstalling J strip Wall panel section split 2 3/4-in. wide joining strip

WSHP-PRC038B-EN_12132025

Document Title:	Water Source Heat Pump Axiom™ Rooftop
Publication Type:	Product Catalog or Quick Reference Guide
Publication Date:	2025-12-13

need service. Use only manufacturer-approved sensors when replacement is required. Application Considerations 18 WSHP-PRC038B-EN Model Number Description Digit 1 — Function G = Rooftop WSHP Digit 2 — Efficiency S = Standard Efficiency Digit 3 — Refrigerant K = R-454B Digit 4, 5, 6 — Nominal Gross

ODR-SVN006B-EN_08232025

. Example of measuring refrigerant line Line Length 18 ODR-SVN006B-EN Refrigerant Line InsulationImportant: The vapor line must always be insulated. Do not allow the liquid line and vapor line to comein direct (metal to metal) contact. Note: The vapor line must always be insulated. Insulatingthe liquid

BAS-SVN231D-EN_10072025

Document Title:	Symbio™ 500 Programmable Controllers
Publication Type:	Installation
Publication Date:	2025-10-07

500Programmable Controller Installation, Operation, and Maintenance (BAS-SVX090*-EN). Mounting Weight of Controller: Mounting surface must support 0.80 lb. (0.364 kg) Environmental Rating (Enclosure): NEMA 1 Plenum Rating: Not plenum rated. The Symbio 500 must be mounted withing a rated enclosure when

RT-SVN043A-EN_07152021

Document Title:	0 to 100% Standard Economizer – Horizontal Foundation™ Packaged Cooling and Gas/Electric 7.5 to 12.5 Tons
Publication Type:	Installation
Publication Date:	2021-07-15

--IInnssttaallllaattiioonn RT-SVN043A-EN 11 Figure 11. Potentiometer and LED locations (W7212 shown) CONTROL CURVE A B C D E CONTROL POINT APPROX. °F (°C) AT 50% RH 73 (23) 70 (21) 67 (19) 63 (17) 55 (13) 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 90 100 80 70 60 50 40 30 20 10 ENTHALP Y—BTU PER