Search Results: TWE*

CLCH-SVX018C-EN_12012025

, unequalthermal stresses, freeze-up and/or corrosion. Proper steam trap installation is necessary for satisfactorycoil performance and service life. For steam trapinstallation:1. Install the steam trap discharge 12 inches below the condensate return connection. Twelve inches providessufficient hydrostatic head

WSHP-SVG004A-EN_12072025

Document Title:	Water Source Heat Pump Axiom™ Variable Speed – Compressor Inverter
Publication Type:	Installation Operation and Maintenance
Publication Date:	2025-12-07

-digit BCD or 16-bit binary (when used with option FR-A8AX) Start signal Forward and reverse rotation or start signal automatic self-holding input (3-wire input) can be selected. Input signals (twelveterminals) Low-speed operation command, Middle-speed operation command, High-speed operation command

WSHP-PRC040B-EN_01122026

Document Title:	Water Source Heat Pump Axiom™ Water-to-Water – EXW 5 to 20 Tons – 60 Hz
Publication Type:	Product Catalog or Quick Reference Guide
Publication Date:	2026-01-12

panel. The unit is equipped with the deluxe 24-volt controlpackage. Components are easily accessible for service, maintenance and start-up. Twenty-four volt thermostat connection ismade at the unit terminal strip located in the left corner of the control box. Anti-Short Cycle TimerThe anti-short cycle

AC-SVX003E-EN_02262026

periodsfor discharge of capacitors. Verify with a CAT III or IVvoltmeter rated per NFPA 70E that all capacitors havedischarged. After disconnecting input power, wait twenty minutes for theDC capacitors to discharge before opening the electricalpanel. Once the electrical panel is opened, use a non

RT-PRC121G-EN_03042026

. Final Filter Options (Available for SX Units only)Final filter section filter options shall mount integral within the blank section unit casing and be accessible by hinged accessdoors. 90-95 Percent, Cartridge, Final Filter Option, Merv 14Available on cooling only SX units. Twelve-inch deep cartridge

SS-SVX014E-EN_03142026

* TWE090K*B* 436768240001 436768420001 TTA120K*C* TWE120K*A* 436768250001 436768250001 TTA120K*D* TWE120K*B* 436768260001 436768430001 TTA150K*D* TWE150K*B* 436768270001 436768440001 TTA180K*D* TWE180K*B* 436768280001 436768280001 TTA180K*C* TWE180K*B* 436768290001 436768290001 TTA240K*D* TWE240K*B

SS-SVX015E-EN_03142026

436768350001 436768470001 TWA090K*D TWE090K*B 436768360001 436768480001 TWA120K*A TWE120K*A 436768370001 436768490001 TWA120K*D TWE120K*B 436768380001 436768500001 TWA150K*D TWE150K*B 436769460001 436769470001 TWA180K*D TWE180K*B 436768390001 436768390001 TWA240K*D TWE240K*B 436768400001 436768400001 TWA300K

SS-SVX016D-EN_03142026

TWE072K*B 398 336 70 102 78 86 59 95 90 92 7.5 TWE090K*A/B 398 336 70 102 78 86 59 95 90 92 10 TWE120K*A/B 454 406 80 124 113 89 82 121 80 123 12.5 TWE150K*B 766 689 171 195 184 139 199 167 148 175 15 TWE180K*B 765 688 170 195 184 139 199 166 148 175 20 TWE240K*B 925 831 261 171 164 235 259 184 149 239

ACC-SVN116J-EN_031420206

for details. Using the parts provided, cap the liquidlines for all units except TWE251/300 and lay out thetubing as shown in the diagrams. This layout ensuresproper oil return to the compressor. 7. Install oil return line between drip leg and compressorsuction tubing. See Figure 7, p. 11. 8. Connect

ACC-SVN184C-EN_03142026

withSymbio™ Controls, 6 to 25 Tons BAYTFMR014: TWE****3*****A*, TWE****1*****A*BAYTFMR015: TWE****4*****A*BAYTFMR016: TWE****W*****A*BAYTFMR017: TWE****D*****A*, TWE****K*****A*BAYTFMR018: TWE****3*A***B*, TWE****1*A***B*BAYTFMR019: TWE****4*A***B*BAYTFMR020: TWE****W*A***B*BAYTFMR021: TWE****D*B***A