Search Results: 18-HD83D1-5B-EN

WSHP-PRC034B-EN_06302025

opportunity to save energy by reducing the need to operatethe boiler or cooling tower. For example, if the water temperature stays in the desired range-between 60ºF (16ºC) and 90ºF(32ºC)-neither the boiler nor the cooling tower need to operate. 18 WSHP-PRC034B-EN In applications such as office buildings

BAS-SVX091B-EN_04082023

, pressure transducerFrom 0 to 2 in. water column (0 to 498 Pa) P2 Spare (recommended for dual duct secondary airflow) 18 BAS-SVX091B-EN Binary InputsTable 8. Binary inputs Binary Inputs Description BI1 Occupancy BI2 Spare BI3 Spare Binary OutputsTable 9. Binary outputs BinaryOutputs Type Output

BAS-PTS032A-EN_12062024

1= Stop2= Auto 2= Auto 1 or 2 2 BAS Chiller Mode Command 1 = Cool3 = Ice 1= Cool 1 to 3 BAS-PTS032A-ENMulti-State Values 18 Symbio™ 800 Integration Points ListModbus™RTAC (UC800) Date: 12/6/2024Reference Document: BAS-SVP083*-EN Object Naming ConventionsThe communicated points for the Symbio™

2309-4870H_02242022

LOCAL APPLICABLE CODES. ALL CUSTOMER CONTROL CIRCUIT WIRING MUST BE COPPER CONDUCTORS ONLY AND HAVE A MINIMUM INSULATION RATING OF 300 VOLTS.EXCEPT AS NOTED ALL CUSTOMER WIRING CONNECTIONS ARE MADE TO CIRCUIT BOARD MOUNTED BOX LUGS WITH A WIRE RANGE OF 14TO 18 AWG. DO NOT RUN LOW VOLTAGE CONTROL

SS-PRC051C-EN_03142026

andEnclosure Assembly Air Handler Return-Air Grille Subbase Isolators(Spring or Rubber) HorizontalDrain VerticalDrain Application Considerations 18 SS-PRC051C-EN Selection ProcedureCooling Capacity1. Calculate the building’s total and sensible cooling loads at design conditions, using standardized

AHR-SVX006B-EN_11052025

be separated frompower wiring unless class 1 wire with proper voltagerating is used.Low voltage control wiring should be 18 Awg, colorcoded (105 degree C minimum). For lengths longer Installation Instructions 18 AHR-SVX006B-EN than 100ft., 16 Awg wire should be used. Make certainthat separation of

DLR-SVX026A-EN_12132025

Document Title:	19-23 Seer 2 Single Zone Ductless Mini-Split Heat Pump
Publication Type:	Installation Operation and Maintenance
Publication Date:	2025-12-13

18 DLR-SVX026A-EN Refrigerant SensorWARNING Leak Detection System Installed!Failure to follow instructions below could result indeath or serious injury or equipment damage.The unit is equipped with electrically powered safetymeasures and must be powered at all times afterinstallation, except during

ACC-SVN240C-EN_10042024

Document Title:	Discharge Air Sensing (DAS) Kit Precedent™ Packaged Rooftop Units
Publication Type:	Installation
Publication Date:	2024-10-04

Installation Figure 13. FIADAST003 and FIADAST005 - Installed Figure 14. FIADAST004 and FIADAST006 - installed 18 ACC-SVN240C-EN Installation • Figure above shows FIADAST009 supply side tubing with a high-heat exchanger. • Factory downflow configuration is shown. For field-installed downflow applications

18-GJ21D1-2B-EN_08212024

, STATE AND LOCAL CODES 18-GJ21D1-2B-EN Models:BAYWA1705SC1AABAYWA2107SC1AABAYWA2308SC1AA Table of ContentsSection 1. Safety Considerations ...... 2Section 2. General Information .......... 3Section 3. Hydronic Coil Assembly .. 4Section 4. Install Hydronic Coil ......... 5Section 5. Piping

PART-SVN92A-EN_06152005

Document Title:	LonTalk Communications Interface for CGAF, RTAA, RTWA and RTUA Chillers
Publication Type:	Installation
Publication Date:	2005-06-15

Installation LonTalk Communications Interface for CGAF, RTAA, RTWA and RTUA Chillers April 2005 PART-SVN92A-EN © American Standard 2005 NOTICE: Warnings and Cautions appear at appropriate sections through-out this literature. Read these carefully. � WARNING: Indicates a potentially hazardous