Search Results: ED*

AH-SLB028-EN_06022023

facilities Higher education Life sciences labs Manufacturing plants Data centers High techmanufacturing facilities Class A commercialreal state Government buildings Each is uniqueEvery custom-built Performance Climate Changer® air handler is designed from scratch and manufactured to meet the building’s

BAS-SVX20K-EN_04152020

Document Title:	Tracer® UC400 Programmable Controller
Publication Type:	Installation Operation and Maintenance
Publication Date:	2020-04-15

file, make any edits, and save them to theUC400. NNoottee:: You can create, edit, and load points, either in Tracer TU, or in the TGP2 Editor. (See theConfiguring and Managing Points TOC book in the Tracer Graphical Programming(TGP2) Editor Help.) Be aware of the maximum point counts as shown in the

BAS-SVX33G-EN_04012020

Document Title:	Power Supply Module PM014 24 Vdc forTrane® inter-module communication buses
Publication Type:	Installation Operation and Maintenance
Publication Date:	2020-04-01

cause equipment damage. 3. Hook the power supply module DIN rail groove to the edge of the DIN rail closest to the IMC pin connectors (Figure 3). 4. Press down on the side of the power supply that holds the DIN rail latch. Press until you hear the latch click. 5. Place a DIN rail end-stop at each end

BAS-SVN111D-EN_05282020

Document Title:	PM014 DC and AC Power Supply Module
Publication Type:	Installation
Publication Date:	2020-05-28

front facingoutward. Refer to BAS-SVX33x-EN for more details. NOTICE Avoid Equipment Damage!Do not use excessive force. Excessive force could cause equipment damage. Perform these steps to mount the power supply module:1. Hook the power supply module DIN rail groove to the edge of the DIN rail closest

SO-SVN025A-EN_08312023

Document Title:	Brushless DC Motor Upgrade for UniTrane Fan-Coil and Force-Flo Air Conditioners
Publication Type:	Installation
Publication Date:	2023-08-31

applications, it is necessary to remove the fan board to change out the motor. The fan board is easily removable, with screws on the front left and right edges of fan boards for vertical units, or on the front left underside and front right underside of the fan board for horizontal units. These screws may

SO-SVN015A-EN_08312023

Document Title:	Agility™ Water-cooled Chiller Filterless Motor Compressor Retrofit
Publication Type:	Installation
Publication Date:	2023-08-31

TERMINAL; 50 X19210282010 WIRE TIE X20600036020 EDGE MOLDING X45050656010 HOSE; DRIVE COOLING, 3/4 INCH I.D. - 200 P.S.I. X32030305030 HOSE CLAMP 453722250001 ASSEMBLY; WIRE TRAY X19051622020 WIRE HARNESS; 1-2 BRANCHING 1000 MM CNT09384 DANFOSS TR200 MARKII CONTROL CARD Table 2. Compressor part numbers

SO-SVN024A-EN_08312023

Document Title:	Variable Frequency Drive Conversion TR1 to TR200 IntelliPak™ I and II and Voyager™ 3 only
Publication Type:	Installation
Publication Date:	2023-08-31

screws with the top of the drive nearest the edge. Excepting large-frame VFDs, there should be room on the adapter plate for fuses to mount below the VFD (Step 6). Fasten the TR200 drive with kit-supplied nuts (NUT KEPS HEX .25-20 ST). 4. Install the TR200 drive with adapter plate utilizing the TR1

SO-SVN038A-EN_08312023

protection for areas that wiring runs may come into contact with sharp edges. • Cable ties to help clean up wiring runs. If the unit is located outside, a cover is required for the display. • The Trane part number for this cover is COV03916. 1 A copy of this manual is shipped with the upgrade kit. 6

RT-PRC060N-EN_12032022

History• Updated General data tables.• Updated Evaporator fan performance tables.• Digit K option removed.• Minor edits to the document. RT-PRC060N-EN 3 Features and Benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Standard

RT-PRC078H-EN_12032022

wiring and also test operation of all unitfunctions. This is another cost and time saving installation feature. InsulationAll panels in the evaporator section of the unit have foil-faced, glass fiber insulation. All base panelshave foil-faced, glass fiber insulation. All edges are either captured or